1. BACKSTG
  2. Guides
  3. How to prepare stems for mixing
Recording and prep

How to prepare stems for mixing

Half the problems in an online mix start before the mix: tracks that don't line up, effects printed by accident, files called "Audio 14". A clean export saves everyone hours.

On this page
  1. Clean up the session
  2. Export without mix effects
  3. Check the levels
  4. Export everything from the same start point
  5. Pick the right format
  6. Add references
  7. Name, check and send
  8. FAQ

In short

  • For a mix, send individual tracks, not grouped stems.
  • No mix effects and no master-bus limiter; 24-bit WAV at the project sample rate.
  • Every track starts at the same point and runs to the end of the song.

Tidy material lets the engineer go straight to the creative part. The method works in any DAW, from Ableton Live and Logic Pro to Pro Tools.

MultitracksStems
What they areIndividual channels: kick, bass, every vocalGroups already mixed: drums, vocals, synths
Used forA full mixStem mastering, remixes, live

A mix almost always needs individual tracks. If in doubt, ask.

Clean up the session

Save a copy of the project and work on that.

  • Delete muted tracks and discarded takes.
  • One comped lead vocal, not six attempts.
  • Clear names: Vox_Lead, Bass_DI, Synth_Arp.

Export without mix effects

Compressors, EQ, reverbs and delays stay off, master limiter included: the engineer chooses the processing. If an effect is part of the sound, export two versions.

21_Order numberVox_LeadTrack name_DRYNo effects.wav
Next to it goes the same track with _FX, effect printed. The engineer picks.

Check the levels

No track should go over 0 dBFS: if a channel hits red, lower it. No need to normalize, at 24-bit a lower level loses no quality.

Export everything from the same start point

Every track starts at bar 1 and runs to the end of the song, even if the instrument only plays in the chorus. The engineer can then line everything up in an empty session.

Exported where the audio starts

  • Song_tracks/
  • Audio 14.wav
  • Audio 14 copy.wav
  • vox bounce.wav
  • synth (starts at 1:12).wav

Exported from bar 1

  • Tides_tracks_260927/
  • 01_Kick.wav
  • 02_Snare.wav
  • 11_Bass_DI.wav
  • 21_Vox_Lead_DRY.wav
  • 22_Vox_Lead_FX.wav
  • 31_Synth_Arp.wav
  • references/
Same length for all of them, plus a few seconds of tail for reverbs and fading notes.

Pick the right format

WAV or AIFF at 24-bit, at the project sample rate.

SettingRecommended
FormatWAV or AIFF, never MP3
Bit depth24-bit (32-bit float if asked)
Sample rateThe project's, no conversion
ChannelsMono for vocals, bass and kick, stereo for stereo sources
DitherNone at 24-bit

Add references

Add your rough mix as you hear it, a file with BPM and key and one or two reference tracks. Find the exact BPM with the BPM counter.

Name, check and send

Number the files, put everything in a folder with title and date, and send one link.

From export to deliveryFour steps: export tracks from bar 1, check three files at random, add rough mix and notes, send one link to the engineer.EXPORTfrom bar 1CHECKthree at randomNOTESrough mix, BPMLINKto the engineerFrom export to deliveryFour steps: export tracks from bar 1, check three files at random, add rough mix and notes, send one link to the engineer.EXPORTfrom bar 1CHECKthree at randomNOTESrough mix, BPMLINKto the engineer
Before sending, open two or three files again: they should play and start at the same point.

For quotes and revisions, read the guide to online mixing and mastering.

FAQ

Should I export tracks with or without effects?

Without mix effects. If an effect is part of the sound, add an FX version.

Why must every track start at the same point?

So the engineer can line them up in an empty session without re-timing them.

What's the difference between multitracks and stems?

Multitracks are the individual channels; stems are groups of tracks already mixed together. A mix needs the individual tracks.